Design Con 2015

Understanding electromagnetic interference sources in touchscreens

Vadim Konradi, Silicon Labs

November 13, 2011

Vadim Konradi, Silicon LabsNovember 13, 2011

Summary: Vadim Konradi of Silicon Labs reviews the various EMI problems associated with projected-capacitance touchscreens  in today’s portable devices. The author then outlines design and optimization techniques to deal with the interference coupling paths. 

A projected-capacitance touchscreen is capable of precise touch location based on a light finger touch to the screen. It determines finger position by measuring miniscule changes in capacitance. Developing a mobile handheld device with a touchscreen interface can be a complex design challenge, especially for projected-capacitance touchscreens, which represent the current mainstream technology for multi-touch interfaces.  A key design consideration in this type of touchscreen application is the impact of electromagnetic interference (EMI) on system performance. In this article we’ll explore the sources of interference-caused performance degradation that can negatively impact touchscreen designs and how to mitigate their effects.

Projected capacitance touchscreen geometry
A typical projected-capacitance sensor is assembled to the underside of a glass or plastic cover lens. Figure 1 shows a simplified edge view of a two-layer type sensor. Transmit (Tx) and receive (Rx) electrodes are drawn in transparent indium tin oxide (ITO), forming a matrix of crossed traces, each Tx-Rx junction having a characteristic capacitance. The Tx ITO lies below the Rx ITO, separated by a thin layer of polymer film and/or optically-clear adhesive (OCA). As shown, the Tx electrode runs from left to right, and the Rx electrode runs into the page.


Figure 1: Sensor geometry reference

Sensor normal operation
The operator’s finger is nominally at ground potential. The Rx is held at ground potential by the touchscreen controller circuit, and the Tx voltage is varied. The changing Tx voltage induces current flow through the Tx-Rx capacitance. A carefully-balanced Rx integrating circuit isolates and measures the charge movement into the Rx. This measured charge indicates the “mutual capacitance” linking Tx and Rx.

Sensor condition: not touched
Figure 2 indicates flux lines in the untouched condition. Without a finger touch, the Tx-Rx field lines occupy considerable space within the cover lens. These fringing field lines project beyond the electrode geometry -- thus the term “projected capacitance.”


Figure 2: Flux lines untouched

Sensor condition: touched
When a finger touches the cover lens, flux lines form between the Tx and finger, displacing much of the Tx-Rx fringing field, as shown in Figure 3. In this manner, the finger touch reduces Tx-Rx mutual capacitance. The charge measurement circuit recognizes this changed capacitance (delta C) and the presence of a finger over the Tx-Rx junction is detected. A map of touch across the panel is generated by making delta C measurements at all intersections in the Tx-Rx matrix.



Figure 3: Flux lines touched

Figure 3 demonstrates an important additional effect: capacitive coupling between the finger and the Rx electrode. Through this path, electrical interference may couple onto the Rx. Some degree of finger-Rx coupling is unavoidable. 

Useful terminology
Interference in projected capacitance touchscreens is coupled through parasitic paths that are not entirely intuitive. The term “ground” is commonly used interchangeably in reference to either the DC circuit reference node or a low-resistance connection into planet Earth. These are not the same terms. In fact, for a portable touchscreen device, this difference is the essential cause of touch-coupled interference. To clarify and prevent confusion, we’ll use the following terminology when assessing touchscreen interference.

  • Earth – connection to planet Earth, for instance via the earth pin of a 3-pin AC mains socket
  • Distributed Earth – capacitive connection of an object to earth
  • DC Ground (GND) – DC reference node of a portable device
  • DC Power – Battery voltage of a portable device. Alternately the output voltage of a charger connected to the portable device, e.g. 5V Vbus for a USB-interface charger.
  • DC VCC – regulated voltage which powers the portable device electronics, including LCD and touchscreen controller
  • Neutral – AC mains return, nominally at earth potential
  • Hot – AC mains voltage, energized with respect to neutral

< Previous
Page 1 of 2
Next >

Loading comments...

Most Commented

  • Currently no items

Parts Search Datasheets.com

KNOWLEDGE CENTER