Debug & Optimization Articles

Design How-To

Basics of real-time measurement, control, and communication using IEEE 1588: Part 5

06 February 2008 Save & Follow Save to My Library Follow Comments

In the fifth in a series on the IEEE 1588 real-time network synchronization protocol, John Eidson... Read More

Design How-To

OCP VIP: A cost effective and robust qualification process for multimedia and telecom SoC designs

09 January 2008 Save & Follow Save to My Library Follow Comments

The authors describe how to set up a rigorous heuristic approach for the OCP verification IP... Read More

Design How-To

Use Cirrus Logic's CS556x/7x/8x ADCs to improve DNL and noise in control system designs

27 December 2007 Save & Follow Save to My Library Follow Comments

How Cirrus Logic's family of high-throughput 16- and 32-bit DeltaSigma ADCs can be used to provide... Read More

Design How-To

Testing wireless devices for 3GPP Release 6 High Speed Uplink Packet Access compatibility

30 November 2007 Save & Follow Save to My Library Follow Comments

A brief tutorial on how to not only test the uplink capability of a high-speed packet access (HSPA)... Read More

Design How-To

Using the 8960 emulator to evaluate audio/video data transfer over HSDPA/WCDMA networks

20 October 2007 Save & Follow Save to My Library Follow Comments

The Agilent 8960 is designed specifically for HSDPA/ W-CDMA UE developers who require performing... Read More

Design How-To

Taking advantage of present and future capabilities of the General Purpose Interface Bus (GPIB)

18 October 2007 Save & Follow Save to My Library Follow Comments

How to make best use of both existing and future new extensions of the General Purpose Interface Bus ... Read More

Design How-To

How effective use of ESL tools can increase your HW/SW system design productivity

05 October 2007 Save & Follow Save to My Library Follow Comments

The use of Electronic System Level tools, complemented by techniques such as Sequential Logic... Read More

Design How-To

Using clock margining for system test boundary stability and early failure prediction

01 October 2007 Save & Follow Save to My Library Follow Comments

This article also explores the use of overclocking techniques for clock margining utilizing... Read More

Design How-To

Locating and measuring sources of EFD and ESD burst interference

1 comments 29 September 2007 Save & Follow Save to My Library Follow Comments

The author describes how to use the E1 Disturbance Immunity Development System to locate the... Read More

Design How-To

Embedded test offers unique value for serial I/O

05 August 2007 Save & Follow Save to My Library Follow Comments

Although incorporating high-speed serial buses into embedded systems solves many problems, the... Read More

Design How-To

Making the right choice in your selection of a signal generator

29 July 2007 Save & Follow Save to My Library Follow Comments

Cindy Ong of NI provides a brief tutorial on the prevalent types of signal generators including... Read More

Design How-To

Use spectrum/signal analysis to limit RF power and spurious noise emissions

29 June 2007 Save & Follow Save to My Library Follow Comments

A brief tutorial on how spectrum and signal analyzers can be used to bring RF system power... Read More

Design How-To

Using LAN eXtensions for Instrumentation (LXI) for automobile electronics testing

26 May 2007 Save & Follow Save to My Library Follow Comments

The LAN eXtensions for Instrumentation (LXI) are an effective and flexible tool in the testing of... Read More

Design How-To

Using three-point current reversal to reduce error in low resistance/power measurements

25 May 2007 Save & Follow Save to My Library Follow Comments

Here's how to offset thermoelectric EMF error in low resistance, low power measurements using a... Read More

Design How-To

Balancing flexibility versus cost in discrete USB transceiver designs

23 May 2007 Save & Follow Save to My Library Follow Comments

With selection of discrete USB transceivers dependent on ESD capability, integrated pull-up... Read More

Design How-To

Dealing with SoC hardware/software design complexity with scalable verification methods

27 April 2007 Save & Follow Save to My Library Follow Comments

To deal with SoC hardware/software design complexity issues we need tools that span the verification ... Read More

Design How-To

A Simple New Approach to Hardware Software Co-Verification

11 March 2007 Save & Follow Save to My Library Follow Comments

Ernst Zwingenberger of El Camino GmbH details how Coverage-driven verification can be performed on... Read More

Design How-To

How to effectively validate new RF technologies

24 February 2007 Save & Follow Save to My Library Follow Comments

With the advent high-speed downlink packet access and high-speed uplink packet access, RF... Read More

Design How-To

Making the transition to 42-volt electrically-powered beltless engine vehicles

11 February 2007 Save & Follow Save to My Library Follow Comments

The transition to nextgen 42 volt electrically-powered beltless engine vehicles will be a difficult... Read More

Design How-To

Using Real Time Spectrum Analyzers to test passive RFID tags

1 comments 07 February 2007 Save & Follow Save to My Library Follow Comments

Real Time Spectrum Analysis is an effective tool for testing RFID-based designs for transient... Read More

All Debug & Optimization Development Articles

All Debug & Optimization Development Articles

Basics of real-time measurement, control, and communication using IEEE 1588: Part 5

OCP VIP: A cost effective and robust qualification process for multimedia and telecom SoC designs

Use Cirrus Logic's CS556x/7x/8x ADCs to improve DNL and noise in control system designs

Testing wireless devices for 3GPP Release 6 High Speed Uplink Packet Access compatibility

Using the 8960 emulator to evaluate audio/video data transfer over HSDPA/WCDMA networks

Taking advantage of present and future capabilities of the General Purpose Interface Bus (GPIB)

How effective use of ESL tools can increase your HW/SW system design productivity

Using clock margining for system test boundary stability and early failure prediction

Locating and measuring sources of EFD and ESD burst interference

Embedded test offers unique value for serial I/O

Making the right choice in your selection of a signal generator

Use spectrum/signal analysis to limit RF power and spurious noise emissions

Using LAN eXtensions for Instrumentation (LXI) for automobile electronics testing

Using three-point current reversal to reduce error in low resistance/power measurements

Balancing flexibility versus cost in discrete USB transceiver designs

Dealing with SoC hardware/software design complexity with scalable verification methods

A Simple New Approach to Hardware Software Co-Verification

How to effectively validate new RF technologies

Making the transition to 42-volt electrically-powered beltless engine vehicles

Using Real Time Spectrum Analyzers to test passive RFID tags

Most Read

The millennium bug revisited

Mastering stack and heap for system reliability: Part 1 – Calculating stack size

Basics of real-time measurement, control, and communication using IEEE 1588: Part 5

Basics of real-time measurement, control, and communication using IEEE 1588: Part 6

Corelis updates boundary-scan tools

Embedded TV video library

Most Commented

Currently no items

Parts Search Datasheets.com

KNOWLEDGE CENTER